DETERMINATION OF HEAVY MACHINES PERFORMANCES BY USING A MEASURING SYSTEM WITH TELEMETRIC SYNCHRONIZATION AND TRANSMISSION OF SIGNALS
Abstract
This paper presents the investigation of importance for determining the dynamic structural response of heavy lifting machines subjected to extreme external effects. A measuring system for the experimental investigation of the dynamics of heavy lifting machines is proposed. It shows the experimental testing results of carrying structures for several classes of hoisting and an export mining machine. The results refer to the most important dynamic parameters. The dynamic parameters also include the duration of transient phenomena in handling lifting structures and structural damping. A technical solution based on the measuring chain that is integrated into the mining export plant information system was developed in the research. The recommendation to choose optimal measuring equipment for this kind of measurement is given to manufacturers and users on the basis of the experience gained in the design and implementation of specific measuring systems. The technical specification of amplifiers and transducers that should be developed for this kind of measurement is also proposed.
References
Radoičić, G. and Jovanović, M. (2017), “Transient simulation of impulse wind effect on a tall shipyard frame structure”, J. Applied Eng. Science (JAES), Vol.15, No.2, 192-202, ISSN 1451-4117, DOI: 10.5937/jaes15-12935.
Radoičić, G. and Jovanović, M. (2013), “Experimental identification of overall structural damping of system”, Strojniški vestnik (J. Mech. Eng), Vol.59, No.4, 260-268.
Radoičić, G., Jovanović, M. and Marinković, D. (2014), “Nonlinear incidental dynamics of frame structures”, Structural Engineering & Mechanics, Vol.52, No.6, 1193-1208.
Jovanović, M., Radoičić, G., Jovanović, V. and Tomić, V. (2015), “Synchronic excitation – a type of malicious dynamic action”, the 21th Int. Conf. MHCL, Vienna, Austria, September.
Jovanović, M., Radoičić, G. and Maneski, T. (2011), “Dynamical eigenvalue identification of heavy structures machine”, the 7th Int. Conf. HM, Vrnjačka Banja, Serbia, June/July.
Jovanović, M. (1990), “Supporting structure level luffing system and driving mechanisms resistance of portal-jib cranes optimization”, Ph.D. Dissertation, University of Niš, Faculty of Mechanical Engineering, Niš, Serbia.
Vladić, J., Jovanović, M., Đokić, R., Kljajin, M. and Karakašić, M. (2015), “Тheoretical and еxperimental analysis of mine еlevator dynamic characteristics”, Tehnički vjesnik, Vol.22, No.4, 1011-1020.
Jovanović, M. and Tomić, V. (2015), “Experimental investigation of mining rope system by magnetic resonance – Service window „Vasa Drecun“ at the Copper Mine Bor”, Research Report, University of Niš, Faculty of Mechanical Enginering, Niš, Serbia.
Jovanović, M., Vladić, J., Tomić, V. and Đokić R. (2015), “Experimental investigation of kinematics and dynamics of the export mining machine ASEA HSDE 2.5 in the Service mine shaft RBB Bor”, Research Report, Faculty of Mechanical Enginering, Niš, Serbia.
Radoičić, G., Jovanović, M. and Arsić, M. (2016), “Experience with an on-board weighing system solution for heavy vehicles”, ETRI J., Vol.38, No.4, 787-797.
Schmidt, H. (2014), “Fatigue analysis of structural adhesive joints under variable amplitude loading”, Ph.D. Dissertation, Fraunhofer Institute for Structural Durability and System Reliability, Darmstadt, Germany.
Radoičić, G. and Jovanović M. (2015), “Design of the dynamic models of mobile elevating work platforms and solutions”, the 3rd Int. Conf. “Mech. Eng. in XXI Century”, Niš, Serbia, September.
Sousa, H., Cavadas, F., Henriques, A., Bento, J. and Figueiras, J. (2013), “Bridge deflection evaluation using strain and rotation measurements”, Smart Structures & Systems, Vol.11, No.4, 365-386.
Arsić, M., Jovanović, M., Radoičić, G., Tomić, V. and Marković, D. (2014), “Technical device solution for kinematics control of mining export machines”, the 5th Int. Conf. “Transport and Logistics – TIL 2014”, Niš, Serbia, June.
Radoičić, G. (2016), “The dynamical behaviour of certain classes of heavy lifting and construction machinery from the aspect of accidental events”, Ph.D. Dissertation, University of Niš, Faculty of Mechanical Engineering, Niš, Serbia.
Hornarbakhsh, A., Nagayama, T., Rana, S., Tominaga, T., Hisazumi, K. and Kanno, R. (2015), “Damage identification of belt conveyor support structure using periodic and isolated local vibration modes”, Smart Structures & Systems, Vol.15, No.3, 787-806.
Gaul, L. (1999), “The influence of damping on waves and vibrations”, Mech. Syst. & Signal Processing, Vol.13, No.1, 1-30.
Rose, T. (2002), “An approach to properly account for structural damping frequency – dependent stiffness/damping, and to use complex matrices in transient response”, Worldwide Aerospace Conf. and Technology Showcase, Toulouse, France, April.
