FLEXURAL BEHAVIOR OF A CONCRETE BEAM REINFORCED WITH METAL REBARS PRODUCED FROM A PSEUDO-ELASTIC NICKEL-TITANIUM ALLOY

Jeanisson Cesar Mariano Silva; Jorge Ferreira; Palloma Muterlle; Douglas Sousa

doi:10.5937/jaes0-38927

Jeanisson Cesar Mariano Silva Department of Fatigue, Fracture and Materials, Faculty of Mechanical Engineering, University of Brasilia, University Campus Darcy Ribeiro, Asa Norte, Brasília – DF, ZIP 70.910-900, Brazil; Department of Materials, Trindade Campus, Goiano Federal Institute, Avenida Wilton Monteiro da Rocha, Setor Cristina II, Trindade – GO, ZIP 75389-269, Brazil https://orcid.org/0000-0001-8368-8979
Jorge Ferreira Department of Fatigue, Fracture and Materials, Faculty of Mechanical Engineering, University of Brasilia, University Campus Darcy Ribeiro, Asa Norte, Brasília – DF, ZIP 70.910-900, Brazil http://orcid.org/0000-0002-1816-9707
Palloma Muterlle Department of Fatigue, Fracture and Materials, Faculty of Mechanical Engineering, University of Brasilia, University Campus Darcy Ribeiro, Asa Norte, Brasília – DF, ZIP 70.910-900, Brazil http://orcid.org/0000-0002-7890-4523
Douglas Sousa Department of Materials, Trindade Campus, Goiano Federal Institute, Avenida Wilton Monteiro da Rocha, Setor Cristina II, Trindade – GO, ZIP 75389-269, Brazil http://orcid.org/0000-0002-9321-3587

DOI: https://doi.org/10.5937/jaes0-38927

Keywords: smart materials, flexural test, special structures

Abstract

The use of concrete in the construction industry is widespread throughout the world, which increases the need for a better characterization of its technical aspects. In particular, there is a need for a better understanding of its poor performance when subjected to dynamic loads, which occurs due to its great stiffness and its little (if any) deformation capacity. Knowing that one of the ways to mitigate the poor behavior of concrete in case of dynamic loads is by improving the deformation capacity or ductility of the metallic reinforcement, the proposal to explore the behavior of a concrete beam reinforced with metallic rebars produced from a pseudo-elastic Nickel-Titanium alloy becomes highly desirable. This experimental research aims to verify the flexural behavior of a concrete beam reinforced with Nickel-Titanium rebars. In this regard, the requirements suggested by the technical standard in force were carefully followed, relying mainly on the international standard ASTM C78. Concrete specimens were produced either reinforced with conventional steel rebars; or reinforced with Nickel-Titanium rebars. The results showed that, although the Nickel-Titanium rebars specimens presented a modulus of rupture 26.48% lower, their displacement was about 642.79% greater in relation to specimens with conventional steel rebars, in addition to presenting a partial recovery of the beam's initial position even after complete concrete breakage.

References

Skrzypczak, I., Słowik, M. (2019). Economical aspects concerning quality control of concrete. Budownictwo i Architektura, 18(1), p. 049-056, DOI: https://doi.org/10.24358/Bud-Arch_19_181_05>

Malyuk, V. V. (2018). Degradation and Sudden Failure of Concrete of Maritime Hydraulic Structures in Severe Hydrometeorological Operating Conditions. IOP Conference Series: Materials Science and Engineering, Vladivostok. Russian Federation, 2–4 October, DOI: https://doi.org/10.1088/1757-899X/463/2/022071>

Shrestha, B., Li C., Hao H., Li, H. (2017). Performance-based seismic assessment of superelastic shape memory alloy-reinforced bridge piers considering residual deformations. Journal of Earthquake Engineering, 21(7), p. 1050–1069, DOI: https://doi.org/10.1080/13632469.2016.1190798>

Ghafoori, E., Neuenschwander, M., Shahverdi, M., Czaderski C., Fontana, M. (2019). Elevated temperature behavior of an iron-based shape memory alloy used for prestressed strengthening of civil structures. Construction Building Materials. 211, p. 437–452. DOI: https://doi.org/10.1016/j.conbuildmat.2019.03.098>

Roh, H., Reinhorn, A. M. (2010). Hysteretic behavior of precast segmental bridge piers with superelastic shape memory alloy bars. Engineering Structrures. 32(10), p. 3394–3403. DOI: https://doi.org/10.1016/j.engstruct.2010.07.013>

Ghafoori, E., Wang, B., Andrawes, B. (2022). Shape memory alloys for structural engineering: An editorial overview of research and future potentials. Engineering Structures, 273, p. 1-5. DOI: https://doi.org/10.1016/j.engstruct.2022.115138>

Sena, G. M., Sivan, S., Weaver, J. D., Prima, M. D. (2020). Larger surface area can reduce nitinol corrosion resistance. npj Materials Degradation, 23 (4), p. 1-8. DOI: https://doi.org/10.1038/s41529-020-00128-3>

Chumlyakov, Y.I., Kireeva, I.V., Vyrodova, A.V., Saraeva, A.A., Pobedennaya, Z.V. (2022). Effect of marforming on superelasticity and shape memory effect of [001]-oriented Ni50.3Ti49.7 alloy single crystals under compression. Journal of Alloys and Compounds, 896, p. 1-9. DOI: https://doi.org/10.1016/j.jallcom.2021.162841>

Ryklina, E., Polyakova, K., Prokoshkin, S. (2020). Comparative Study of Shape Memory Effects in Ni-Rich Ti–Ni Alloy After Training in Various Phase States. Shape Memory and Superelasticity, 6, p. 157-169. DOI: https://doi.org/10.1007/s40830-020-00279-x>

Auricchio, F., Coda, A., Reali, A., Urbano, M. (2009). SMA Numerical Modeling Versus Experimental Results: parameter identification and model prediction capabilities. Journal of Materials Engineering and Performance, 18(5-6), p. 649-654. DOI: https://doi.org/10.1007/s11665-009-9409-7>

Silva, J.C.M. (2015). Evaluation of NiTi-Concrete bond for Applications in Civil Construction, p. 86, Dissertation (Master's), Postgraduate in Integrity of Engineering Materials, University of Brasília, Brasília - DF. DOI: https://dx.doi.org/10.26512/2015.https://dx.doi.org/10.D.19734