STRENGTH STUDY OF MACHINE TOOL BEDS WITH CURVILINEAR STIFFENERS FROM POLYMER CONCRETE

Alexandra Berg; Oxana Nurzhanova; Andrey Berg; Olga Zharkevich; Tatyana Nikonova; Vassiliy Yurchenko; Gulnara Taimanova

doi:10.5937/jaes0-51243

Alexandra Berg ABYLKAS SAGINOV KARAGANDA TECHNICAL UNIVERSITY https://orcid.org/0000-0003-0528-640X
Oxana Nurzhanova ABYLKAS SAGINOV KARAGANDA TECHNICAL UNIVERSITY
Andrey Berg ABYLKAS SAGINOV KARAGANDA TECHNICAL UNIVERSITY https://orcid.org/0000-0002-8907-1803
Olga Zharkevich ABYLKAS SAGINOV KARAGANDA TECHNICAL UNIVERSITY https://orcid.org/0000-0002-4249-4710
Tatyana Nikonova ABYLKAS SAGINOV KARAGANDA TECHNICAL UNIVERSITY https://orcid.org/0000-0002-6539-1263
Vassiliy Yurchenko ABYLKAS SAGINOV KARAGANDA TECHNICAL UNIVERSITY https://orcid.org/0000-0002-6543-1632
Gulnara Taimanova Al-Farabi Kazakh National University https://orcid.org/0000-0003-4015-0372

DOI: https://doi.org/10.5937/jaes0-51243

Keywords: strength, helix, curved ribs, stiffness, composite

Abstract

This study addresses enhancing the strength of metal-cutting machine tool beds made from polymer concrete by optimizing the internal cross-section design through spiral stiffeners. Key factors influencing the bed’s strength include the composite preparation technology, the mixing speed (600 - 800 rpm), and duration (3 - 4 minutes). A strong correlation exists between spiral pitch, mixing speed, mixing time, and the bed’s strength.

References

Kumar, R., Jain, A., Mishra, S. K., Joshi, M., Singh, K., & Jain, R. (2021). Comparative structural analysis of CNC milling machine bed using Al-SIC/graphite, Al alloy and Al-SIC composite material. Materials Today: Proceedings, vol. 51, Part 1, 735-741 DOI: 10.1016/j.matpr.2021.06.219

Kępczak, N., PawłowskI, W., Kaczmarek, Ł. (2015) Cast iron and mineral cast applied for machine tool bed - dynamic behavior analysis. Archives of metallurgy and materials, vol. 60, issue 2, 1023-1029, DOI: 10.1515/amm-2015-0254

Srinivasan, S., Subramanyam, B. (2016) Design and Structural Analysis of CNC Milling Machine Bed with Composite Material. Imperial Journal of Interdisciplinary Research (IJIR), vol. 2, issue 12, 147-151 ISSN: 2454-1362, http://www.onlinejournal.in

Ma, Ya., i Li, F., Wang, L., Wang, G., Kong, L. (2021) Life cycle carbon emission assessments and comparisons of cast iron and resin mineral composite machine tool bed in China, vol. 113, 1143 - 1152 DOI: 10.1007/s00170-021-06656-9

Shukla, A., Singh, D. (2018) Design and analysis of machine tool bed JETIR September 2018, vol. 5, issue 9, 580 – 588 ISSN-2349-5162, www.jetir.org

Cortés F., Castillo, G. (2007) Comparison between the dynamical properties of polymer concrete and grey cast iron for machine tool applications. Materials & Design, 28(5), 1461-1466 DOI: 10.1016/j.matdes.2006.03.012

Haddad H., Kobaisi M. (2012) Optimization of the polymer concrete used for manufacturing bases for precision tool machines, Composites Part B: Engineering, vol. 43, issue 8, 3061-3068, DOI: 10.1016/j.compositesb.2012.05.003

Dunaj, P., Dolata, M., Tomaszewski, J., Majda, P. (2022) Static stiffness design of vertical lathe with steel-polymer concrete frame. The International Journal of Advanced Manufacturing Technology, 121(2), DOI: 10.1007/s00170-022-09391-x

Bedi, R., Chandra, R., Singh, S. Reviewing some properties of polymer concrete (2014) The Indian Concrete Journal, vol. 88, issue 8, 47-68

Jiangmin, D. The new shape forming technology of composite concrete machine tool beds (2010) International conference on mechanic automation and control engineering DOI: 10.1109/MACE.2010.5536583

Murugan S., Thyla, P. (2015) Investigation on dynamic analysis of VMC bed using epoxy composite carbon, Sci. Tech, 7/4, 66-75 ISSN 0974 – 0546, http://www.applied-science-innovations.com

Lia, B., Honga, J., Wanga, Z., Wua, W., Chen, Y. (2012) Optimal design of machine tool bed by load bearing topology Identification with weight distribution criterion Procedia CIRP 3, 626 – 631 DOI: 10.1016/j.procir.2012.07.107

Lucchetta, G., P. Bariani, F. (2010) Sustainable design of injection moulded parts by material intensity reduction. CIRP Annals, 59(1), 33-36 DOI: 10.1016/j.cirp.2010.03.092

Jafari, K., Ta, M., Joshaghani, A., Ozbakkaloglu, T. (2018) Optimizing the mixture design of polymer concrete: An experimental investigation. Construction and Building Materials 167, 185-196 DOI: 10.1016/j.conbuildmat.2018.01.191

Zhetessova G., Nikonova, T., Łukasz G., Berg, A.,Yurchenko, V., Zharkevich, O., Kalinin A. A Comparative Analysis of the Dynamic Strength Properties of the Long Guides of Intelligent Machines for a New Method of the Thermal Spraying of Polymer Concrete Appl. Sci. 2022, 12, 10376. doi.org/ 10.3390/app122010376

Jo, B., Park, S., Kim, D. (2008) Mechanical properties of nano-MMT reinforced polymer composite and polymer concrete. Construction and Building Materials, vol. 22,.14-20 https://doi.org/10.1016/j.conbuildmat.2007.02.009

Berg, A., Nikonova, T., Dandybaev E., Yesyunin, A., Yurchenko V. (2023) Frame of metal cutting machine tool made from polymer concrete with optimized geometry for processing long parts (utility model patent № 8332 of the Republic of Kazakhstan)

Nikonova, T., Gierz, Ł., Berg, A., Turla, V., Warguła, Ł., Yurchenko, V., Abdugaliyeva, G., Zhunuspekov, D., Wieczorek, B., Robakowska, M., Dandybaev E. Comparative analysis of strength fatigue properties and abrasive wear resistance for a new composition of polymer concrete coated with metal alloy powders. Coatings 2023, 13, 586. https://doi.org/10.3390/ coatings13030586

Sherov, K., Mardonov, B., Zharkevich, O., Mirgorodskiy S., Gabdyssalyk R., Smakova N, Akhmedov, K., Imanbaev, Y. (2020) Studying the process of tooling cylindrical gears. Journal of Applied Engineering Science, 18(3), 327–332 DOI: 10.5937/jaes18-23794

Zharkevich, O., Nurzhanova, O., Zhunuspekov, D., Naboko, Ye., Buzauova, T., Abdugaliyeva, G., Mateshov, A., Bessonov, A. (2023) Determination of optimal hardfacing modes for recovering electric motor shafts. Tehnički vjesnik, 30, 3, 951-957 https://doi.org/10.17559/TV-20220719104215

Zharkevich, O., Nikonova, T., Gierz, Ł., Berg, A., Berg, A., Zhunuspekov, D., Warguła, Ł., Łykowski W, Fryczyński K. (2023) Parametric optimization of a new gear pump casing based on weight using a finite element method. Applied Sciences, 13(22), 12154. https://doi.org/10.3390/app132212154

Yelemessov, K., Krupnik, L., Bortebayev, S., Beisenov, B., Baskanbayeva, D. (2020) Polymer concrete and fibre concrete as efficient materials for manufacture of gear cases and pumps. E3S Web of Conferences, 168 (12), 00018 DOI: 10.1051/e3sconf/202016800018

Baskanbayeva, D., Krupnik, L., Yelemessov, K., Bortebayev, S., Igbayeva, A. (2020) Justification of rational parameters for manufacturing pump housings made of fibroconcrete. Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu, № 5, 68 - 74 DOI: 10.33271/nvngu/20205/