OPTIMIZATION OF UNMANNED AERIAL VEHICLE STRUCTURES USING CARBON PLASTIC MATERIALS
Abstract
This research explores the potential of using carbon plastic composite materials to optimize the structure of unmanned aerial vehicles (UAVs). The main issue addressed is reducing the weight of drones while increasing their strength and aerodynamic stability. The study found that the specific strength of carbon composites is 1500 MPa/g/cm³, which is three times higher than that of conventional materials. Additionally, the structural vibration resistance increased by 25-30%, and the weight was reduced by 25%. These results are explained by the low density of the material (1.55 – 1.65 g/cm³) and optimal distribution of stresses in the structure. A key feature of the research is the use of a method based on actual CAD modeling and numerical simulations, and the assessment of the efficiency of 3D printing and Out-of-Autoclave technologies, which supports its industrial potential. The findings can be applied in the construction of lightweight, reliable, and energy-efficient drones. Practical applications of these materials include military, agricultural, and emergency rescue systems, with usage conditions in environments with moderate temperatures and vibrational loads.
References
Mohsan, S. A. H., Khan, M. A., Noor, F., Ullah, I., & Alsharif, M. H. (2022). Towards the unmanned aerial vehicles (UAVs): A comprehensive review. Drones, 6(6), 147. https://doi.org/10.3390/drones6060147
Salinas, J. C., & Lewandowski, T. (2025). Blue unmanned aircraft systems explained: The current drone market, flight regulations, and debunking common misconceptions. Transportation Research Record, 2679(1), 1802–1813. https://doi.org/10.1177/03611981241257509
Mallick, P. K. (2007). Fiber-reinforced composites: Materials, manufacturing, and design. CRC Press. https://doi.org/10.1201/9781420005981
Jelača, M. S., & Boljević, A. (2016). Critical success factors and negative effects of development: The Boeing 787 Dreamliner. Strategic Management, 21(1). https://smjournal.rs/index.php/home/article/view/90/67
Milewski, M., Wróbel, J., Kierzkowski, A., & Vališ, D. (2025). Experimental and numerical modal analysis of an unmanned aerial vehicle's composite wing. Simulation Modelling Practice and Theory, 142, 103106. https://doi.org/10.1016/j.simpat.2025.103106
Verma, A. K., Pradhan, N. K., Nehra, R., & Prateek. (2018, December). Challenge and advantage of materials in design and fabrication of composite UAV. In IOP Conference Series: Materials Science and Engineering (Vol. 455, No. 1, p. 012005). IOP Publishing. https://doi.org/10.1088/1757-899X/455/1/012005
Goh, G. D., Toh, W., Yap, Y. L., Ng, T. Y., & Yeong, W. Y. (2021). Additively manufactured continuous carbon fiber-reinforced thermoplastic for topology optimized unmanned aerial vehicle structures. Composites Part B: Engineering, 216, 108840. https://doi.org/10.1016/j.compositesb.2021.108840
Fantuzzi, N., Dib, A., Babamohammadi, S., Campigli, S., Benedetti, D., & Agnelli, J. (2024). Mechanical analysis of a carbon fibre composite woven composite laminate for ultra-light applications in aeronautics. Composites Part C: Open Access, 14, 100447. https://doi.org/10.1016/j.jcomc.2024.100447
Sheikhi, M. R., Gürgen, S., Altuntas, O., & Sofuoğlu, M. A. (2023). Anti-impact and vibration-damping design of cork-based sandwich structures for low-speed aerial vehicles. Archives of Civil and Mechanical Engineering, 23(2), 71. https://doi.org/10.1007/s43452-023-00613-x
Vijayalakshmi, S., Sekar, A. V., Hassan, A. M., Arputharaj, B. S., Jayakumar, S. S., Al-bonsrulah, H. A., & Raja, V. (2023). Multi-perspective structural integrity-based computational investigations on airframe of gyrodyne-configured multi-rotor UAV. Reviews on Advanced Materials Science, 62(1), 20230147. https://doi.org/10.1515/rams-2023-0147
Kumar, V. A., Sivaguru, M., Janaki, B. R., Eswar, K. S., Kiran, P., & Vijayanandh, R. (2021, March). Structural optimization of frame of the multi-rotor unmanned aerial vehicle through computational structural analysis. In Journal of Physics: Conference Series (Vol. 1849, No. 1, p. 012004). IOP Publishing. https://doi.org/10.1088/1742-6596/1849/1/012004
Kurnyta, A., Zielinski, W., Reymer, P., Dragan, K., & Dziendzikowski, M. (2020). Numerical and experimental UAV structure investigation by pre-flight load test. Sensors, 20(11), 3014. https://doi.org/10.3390/s20113014
Meiirbekov, A., Amantayeva, A., Tokbolat, S., Suleimen, A., Sarfraz, S., & Shehab, E. (2021, October). Carbon fiber composites application and recycling in Kazakhstan and neighboring countries. In International Conference on Transdisciplinary Engineering (pp. 425–434). IOS Press. https://doi.org/10.3233/ATDE210122
Sharifov, D., Niyazbekova, R., Mirzo, A., Shansharova, L., Serekpayeva, M., Aldabergenova, S., & Bembenek, M. (2024). The study of composite materials properties based on polymers and nano-additives from industrial wastes from Kazakhstan. Materials, 17(12), 2959. https://doi.org/10.3390/ma17122959
Azarov, A. V., Antonov, F. K., Golubev, M. V., Khaziev, A. R., & Ushanov, S. A. (2019). Composite 3D printing for the small size unmanned aerial vehicle structure. Composites Part B: Engineering, 169, 157–163. https://doi.org/10.1016/j.compositesb.2019.03.073
Hairi, S. M. F. B. S., Saleh, S. J. M. B. M., Ariffin, A. H., & Omar, Z. B. (2023). A review on composite aerostructure development for UAV application. In Green Hybrid Composite in Engineering and Non-Engineering Applications (pp. 137–157). https://doi.org/10.1007/978-981-99-1583-5_9
Anand, S., & Mishra, A. K. (2022). High-performance materials used for UAV manufacturing: Classified review. International Journal of All Research Education and Scientific Methods, 10(7), 2455–6211.
Macias, J. D., Bante-Guerra, J., Cervantes-Alvarez, F., Rodríguez-Gattorno, G., Arés-Muzio, O., Romero-Paredes, H., & Alvarado-Gil, J. J. (2019). Thermal characterization of carbon fiber-reinforced carbon composites. Applied Composite Materials, 26(1), 321–337. https://doi.org/10.1007/s10443-018-9694-0
Idris, M. K., Qiu, J., Melenka, G. W., & Grau, G. (2020). Printing electronics directly onto carbon fiber composites: UAV wings with integrated heater for de-icing. Engineering Research Express, 2(2), 025022. https://doi.org/10.1088/2631-8695/ab8e24
Dell’Anno, G., Partridge, I., Cartié, D., Hamlyn, A., Chehura, E., James, S., & Tatam, R. (2012). Automated manufacture of 3D reinforced aerospace composite structures. International Journal of Structural Integrity, 3(1), 22–40. https://doi.org/10.1108/17579861211209975
Chen, Y., Zhang, J., Li, Z., Zhang, H., Chen, J., Yang, W., & Li, Y. (2023). Manufacturing technology of lightweight fiber-reinforced composite structures in aerospace: Current situation and toward intellectualization. Aerospace, 10(3), 206. https://doi.org/10.3390/aerospace10030206
Wang, L., Zhang, Z., Yin, W., Chen, H., Zhou, G., Ma, H., & Tan, D. (2024). Parameters impact analysis of CFRP defect detection system based on line laser scanning thermography. Nondestructive Testing and Evaluation, 39(5), 1169–1194. https://doi.org/10.1080/10589759.2023.2247137
Chen, H., Zhang, Z., Yin, W., Wang, Q., Li, Y., & Zhao, C. (2022). Surface defect characterization and depth identification of CFRP material by laser line scanning. NDT & E International, 130, 102657. https://doi.org/10.1016/j.ndteint.2022.102657
Çelebi, M., Çanakçı, A., & Özkaya, S. (2025). Comparative study of powder characteristics and mechanical properties of Al2024 nanocomposites reinforced with carbon-based additives. Advanced Powder Technology, 36(4), 104835. https://doi.org/10.1016/j.apt.2025.104835
Turan, F. (2024). The mechanical characterization of carbon-based nanoparticle reinforced epoxy composites: A comparative study. Eskişehir Technical University Journal of Science and Technology A, 25(2), 208–221. https://doi.org/10.18038/estubtda.1381745
Patel, M., Pardhi, B., Chopara, S., & Pal, M. (2018). Lightweight composite materials for automotive: A review.
Shehab, E., Meiirbekov, A., Amantayeva, A., Suleimen, A., Tokbolat, S., & Sarfraz, S. (2021). A cost modelling system for recycling carbon fiber-reinforced composites. Polymers, 13(23), 4208. https://doi.org/10.3390/polym13234208
Taissariyeva, K., et al. (2025). Analysis and modeling of environmental monitoring using multicopters. International Journal of Innovative Research and Scientific Studies, 8(3), 2947–2960. https://doi.org/10.53894/ijirss.v8i3.7119
Sabibolda, A., Tsyporenko, V., Smailov, N., Tsyporenko, V., & Abdykadyrov, A. (2024, August). Estimation of the time efficiency of a radio direction finder operating on the basis of a searchless spectral method. In IFToMM Asian Conference on Mechanism and Machine Science (pp. 62–70). Springer. https://doi.org/10.1007/978-3-031-67569-0_8
Smailov, N., Zhadiger, T., Tashtay, Y., Abdykadyrov, A., & Amir, A. (2024). Fiber laser-based two-wavelength sensors for detecting temperature and strain on concrete structures. International Journal of Innovative Research and Scientific Studies, 7(4), 1693–1710. https://doi.org/10.53894/ijirss.v7i4.3481
Kuttybayeva, A., Abdykadyrov, A., Tolen, G., Burdin, A., Malyugin, V., & Kiesewetter, D. (2024, October). Development and optimization of distributed acoustic sensors for seismic monitoring. In 2024 International Conference on Electrical Engineering and Photonics (EExPolytech) (pp. 64–67). IEEE. https://doi.org/10.1109/EExPolytech62224.2024.10755702
Abdykadyrov, A., Marxuly, S., Tolen, G., Kuttybayeva, A., Abdullayev, M., & Sharipova, G. (2024). Optimization of data transmission in sensor networks for enhanced control of ozonator efficiency. Eastern-European Journal of Enterprise Technologies, 132(2). https://doi.org/10.15587/1729-4061.2024.318585
Kuttybayeva, A., Abdykadyrov, A., Tolen, G., Burdin, A., Malyugin, V., & Kiesewetter, D. (2024, October). Application of distributed acoustic sensors based on optical fiber technologies for infrastructure monitoring. In 2024 International Conference on Electrical Engineering and Photonics (EExPolytech) (pp. 23–26). IEEE. https://doi.org/10.1109/EExPolytech62224.2024.10755937
Abdykadyrov, A., Smailov, N., Sabibolda, A., Tolen, G., Dosbayev, Z., Ualiyev, Z., & Kadyrova, R. (2024). Optimization of distributed acoustic sensors based on fiber optic technologies. Eastern-European Journal of Enterprise Technologies, 131(5). https://doi.org/10.15587/1729-4061.2024.313455
Smailov, N., Tsyporenko, V., Sabibolda, A., Tsyporenko, V., Abdykadyrov, A., Kabdoldina, A., & Kadyrova, R. (2024). Streamlining digital correlation-interferometric direction finding with spatial analytical signal. Informatyka, Automatyka, Pomiary w Gospodarce i Ochronie Środowiska, 14(3), 43–48. https://doi.org/10.35784/iapgos.6177
Smailov, N., Tsyporenko, V., Sabibolda, A., Tsyporenko, V., Kabdoldina, A., Zhekambayeva, M., & Abdykadyrov, A. (2023). Improving the accuracy of a digital spectral correlation-interferometric method. Eastern-European Journal of Enterprise Technologies, 125(9). https://doi.org/10.15587/17294061.2023.288397
Sabibolda, A., Tsyporenko, V., Tsyporenko, V., Smailov, N., Zhunussov, K., Abdykadyrov, A., & Duisenov, N. (2022). Improving the accuracy and performance speed of the digital spectral-correlation method. Eastern-European Journal of Enterprise Technologies, 1(9). https://doi.org/10.15587/1729-4061.2022.252561
Battawi, A. A., & Abed, B. H. (2022). Experimental, theoretical and numerical investigation of creep characteristics of fish scale powder chicken feather filled polyester composites. Journal of Applied Engineering Science, 20(4), 1307–1316. https://doi.org/10.5937/jaes0-37488
Cajzek, R. (2016). An unmanned aerial vehicle for multi-purpose tasks in construction industry. Journal of Applied Engineering Science, 14(2), 314–327. https://doi.org/10.5937/jaes14-10918
