The Effect of Electroslag Remelting on the Cleanliness of CrNiMoWMnV Ultrahigh-Strength Steels

  • Mohammed Ali University of Oulu, Materials and Mechanical Engineering, Centre for Advanced Steels Research, 90014 Oulun yliopisto, Finland, Finland Steel Technology Department, Central Metallurgical Research and Development Institute (CMRDI), Cairo, Egypt
  • David Porter University of Oulu, Materials and Mechanical Engineering, Centre for Advanced Steels Research, 90014 Oulun yliopisto, Finland, Finland
  • Jukka Kömi University of Oulu, Materials and Mechanical Engineering, Centre for Advanced Steels Research, 90014 Oulun yliopisto, Finland, Finland
  • Eetu-Pekka Heikkinen University of Oulu, Laboratory of Process Metallurgy, Oulu, Finland
  • Mamdouh Eissa Steel Technology Department, Central Metallurgical Research and Development Institute (CMRDI), Cairo, Egypt
  • Hoda El Faramawy Steel Technology Department, Central Metallurgical Research and Development Institute (CMRDI), Cairo, Egypt
  • Taha Mattar Steel Technology Department, Central Metallurgical Research and Development Institute (CMRDI), Cairo, Egypt

Abstract


The effect of electroslag remelting (ESR) using CaF2:Al2O3:CaO (70:15:15) synthetic slag on the cleanliness of ultrahigh-strength steels (UHSS) has been investigated. Three grades of UHSS were designed and produced via an induction furnace melting and then refined using ESR. The produced ingots were hot forged with start forging temperature 1100 oC and end forging temperature 950 oC then air cooled. Investigation of the non-metallic inclusions in produced steels has been carried out using field emission scanning electron microscopy and laser scanning confocal microscopy.  Thermodynamic calculations for the expected NMIs formed in the investigated steels with and without ESR have been performed using FactSage 7.2 software while HSC Chemistry version 9.6.1 has been used to calculate the standard Gibbs free energy (DG0). Depending on the steel composition and as a result of ESR; the total impurity levels (TIL% = O% + N% + S%) and NMI contents decreased by as much as 46% and 62% respectively. The NMIs were classified into four major classes: oxides, sulphides, nitrides and complex multiphase inclusions. ESR brings about large changes in the area percentages, number densities, maximum equivalent circle diameters and the chemical composition of the various inclusions. Most MnS inclusions were removed although some were re-precipitated on oxide or nitrides inclusions leading to multiphase inclusions with an oxide or nitride core surrounded by sulphide, e.g. (MnS.Al2O3) and (MnS. TiN). Also, some sulphides are modified by Ca, forming (CaMn)S and CaS.Al2O3. Some nitrides like TiN and (TiV)N are nucleated and precipitated during the solidification phase. Al2O3 inclusions were formed as a result of the addition of Al as a deoxidant to the ESR slag to prevent penetration of oxygen to the molten steel.

References

D. Morris, D.R. James, Eglin steel-a low alloy high strength composition, US 7,537,727 B2, 2009.

L.U. Yan, S.U. Jie, W. Junhua, X.I.E. Gang, Y. Zhuoyue, Effect of W on microstructure of high strength and toughness steels, Acta Metallurgica Sinica (English Letters). 24 (2011) 423–431. doi:10.11890/1006-7191-116-423.

G. Vartanov, High strength military steel, US 8,414.713 B2, 2013.

Z.G. Yang, S.X. Li, J.M. Zhang, J.F. Zhang, G.Y. Li, Z.B. Li, W.J. Hui, Y.Q. Weng, The fatigue behaviors of zero-inclusion and commercial 42CrMo steels in the super-long fatigue life regime, Acta Materialia. 52 (2004) 5235–5241. doi:10.1016/j.actamat.2004.06.031.

M.D. Chapetti, T. Tagawa, T. Miyata, Ultra-long cycle fatigue of high-strength carbon steels part I: review and analysis of the mechanism of failure, Materials Science and Engineering: A. 356 (2003) 227–235. doi:10.1016/S0921-5093(03)00135-7.

M.D. Chapetti, T. Tagawa, T. Miyata, Ultra-long cycle fatigue of high-strength carbon steels part II: estimation of fatigue limit for failure from internal inclusions, Materials Science and Engineering: A. 356 (2003) 236–244. doi:10.1016/S0921-5093(03)00136-9.

L.H. He, J.H. Zhao, Evolution of stresses in composites with rigid inclusions during interface diffusion: a two-dimensional case, International Journal of Engineering Science. 38 (2000) 1181–1195. doi:10.1016/S0020-7225(99)00070-1.

C. Bertrand, J. Molinero, S. Landa, R. Elvira, M. Wild, G. Barthold, P. Valentin, H. Schifferl, Metallurgy of plastic inclusions to improve fatigue life of engineering steels, Ironmaking & Steelmaking. 30 (2003) 165–169. doi:10.1179/030192303225001667.

Y. Ren, Y. Wang, S. Li, L. Zhang, X. Zuo, S.N. Lekakh, K. Peaslee, Detection of Non-metallic Inclusions in Steel Continuous Casting Billets, Metallurgical and Materials Transactions B. 45 (2014) 1291–1303. doi:10.1007/s11663-014-0042-y.

E.A. Chichkarev, Modeling the coagulation and removal of nonmetallic inclusions during the injection of an inert gas into a melt, Metallurgist. 54 (2010) 236–243. doi:10.1007/s11015-010-9286-1.

D. Janke, Z. Ma, P. Valentin, A. Heinen, Improvement of Castability and Quality of Continuously Cast Steel., ISIJ International. 40 (2000) 31–39. doi:10.2355/isijinternational.40.31.

S. Yang, Q. Wang, L. Zhang, J. Li, K. Peaslee, Formation and Modification of MgO·Al2O3-Based Inclusions in Alloy Steels, Metallurgical and Materials Transactions B. 43 (2012) 731–750. doi:10.1007/s11663-012-9663-1.

P. Kaushik, J. Lehmann, M. Nadif, State of the Art in Control of Inclusions, Their Characterization, and Future Requirements, Metallurgical and Materials Transactions B. 43 (2012) 710–725. doi:10.1007/s11663-012-9646-2.

L. Zhang, B.G. Thomas, State of the Art in Evaluation and Control of Steel Cleanliness., ISIJ International. 43 (2003) 271–291. doi:10.2355/isijinternational.43.271.

B.-H. Yoon, K.-H. Heo, J.-S. Kim, H.-S. Sohn, Improvement of steel cleanliness by controlling slag composition, Ironmaking & Steelmaking. 29 (2002) 214–217. doi:10.1179/030192302225004160.

H.S. Kim, H.-G. Lee, K.-S. Oh, Precipitation behavior of MnS on oxide inclusions in Si/Mn deoxidized steel, Metals and Materials. 6 (2000) 305–310. doi:10.1007/BF03028076.

A.K. Vaish, G.V.R. Iyer, P.K. De, B.A. Lakra, A.K. Chakrabarti, P. Ramachandrarao, Electroslag remelting-Its status, mechanism and refining aspects in the production of quality steels, Journal of Metallurgy and Materials Science. 42 (2000) 11–29.

W.E. Duckworth, G. Hoyle, Electro-slag refining, Chapman & Hall, 1969.

U. Biebricher, H. Scholz, Electro slag remelting technologies in the past and in the future, Metallurgical Plant and Technology International(Germany). 22 (1998) 36–38.

T. Mattar, Effect of ESR and nitrogen alloying on the cleanliness of M41 steel, Journal of Materials Sciences and Technology (MST). 17 (2009) 35–46.

T. Mattar, Electro-Slag Remelting of AISI M41 High-Speed Tool Steel Scrap, in: 6th International Tooling Conference, Karlstad, 2002: pp. 10–13.

Y.-W. Dong, Z.-H. Jiang, Y.-L. Cao, A. Yu, D. Hou, Effect of Slag on Inclusions During Electroslag Remelting Process of Die Steel, Metallurgical and Materials Transactions B. 45 (2014) 1315–1324. doi:10.1007/s11663-014-0070-7.

M. Ali, M. Eissa, H.E. Faramawy, D. Porter, J. Kömi, M.F. El-Shahat, T. Mattar, Electroslag Refining of CrNiMoWMnV Ultrahigh-Strength Steel, Journal of Minerals and Materials Characterization and Engineering. 05 (2017) 385–407. doi:10.4236/jmmce.2017.56032.

M. Li, D. Wilkinson, K. Patchigolla, Comparison of Particle Size Distributions Measured Using Different Techniques, Particulate Science and Technology. 23 (2005) 265–284. doi:10.1080/02726350590955912.

C.W. Bale, E. Bélisle, P. Chartrand, S.A. Decterov, G. Eriksson, A.E. Gheribi, K. Hack, I.-H. Jung, Y.-B. Kang, J. Melançon, A.D. Pelton, S. Petersen, C. Robelin, J. Sangster, P. Spencer, M.-A. Van Ende, FactSage thermochemical software and databases, 2010–2016, Calphad. 54 (2016) 35–53. doi:10.1016/j.calphad.2016.05.002.

HSC Chemistry, (n.d.). http://www.hsc-chemistry.com/.

J. Burja, F. Tehovnik, M. Godec, J. Medved, B. Podgornik, R. Barbic, Effect of electroslag remelting on the non-metallic inclusions in H11 tool steel, Journal of Mining and Metallurgy, Section B: Metallurgy. 54 (2018) 51–57. doi:10.2298/JMMB160623053B.

S. Li, G. Cheng, Z. Miao, W. Dai, L. Chen, Z. Liu, Evolution of Oxide Inclusions in G20CrNi2Mo Carburized Bearing Steel during Industrial Electroslag Remelting, ISIJ International. (2018). doi:10.2355/isijinternational.ISIJINT-2018-072.

H. Doostmohammadi, P.G. Jönsson, J. Komenda, S. Hagman, Inclusion Characteristics of Bearing Steel in a Runner after Ingot Casting, Steel Research International. 81 (2010) 142–149. doi:10.1002/srin.200900106.

K. Oikawa, K. Ishida, T. Nishizawa, Effect of Titanium Addition on the Formation and Distribution of MnS Inclusions in Steel during Solidification., ISIJ International. 37 (1997) 332–338. doi:10.2355/isijinternational.37.332.

M. Wakoh, T. Sawai, S. Mizoguchi, Effect of S Content on the MnS Precipitation in Steel with Oxide Nuclei., ISIJ International. 36 (1996) 1014–1021. doi:10.2355/isijinternational.36.1014.

R.H. Nafziger, The Electroslag Melting Process, U.S. Bureau of Mines, 1974.

U.B. Pal, C.J. MacDonald, E. Chiang, W.C. Chernicoff, K.C. Chou, J. Van Den Avyle, M.A. Molecke, D. Melgaard, Behavior of ceria as an actinide surrogate in electroslag remelting and refining slags, Metallurgical and Materials Transactions B. 32 (2001) 1119–1128. doi:10.1007/s11663-001-0100-0.

M. Maeda, T. Yahata, K. Mitugi, T. Ikeda, Aluminothermic Reduction of Titanium Oxide, Materials Transactions, JIM. 34 (1993) 599–603. doi:10.2320/matertrans1989.34.599.

S. Duan, X. Shi, M. Mao, W. Yang, S. Han, H. Guo, J. Guo, Investigation of the Oxidation Behaviour of Ti and Al in Inconel 718 Superalloy During Electroslag Remelting, Scientific Reports. 8 (2018). doi:10.1038/s41598-018-23556-3.

B. Arh, B. Podgornik, J. Burja, Electroslag remelting: A process overview, Materiali in Tehnologije. 50 (2016) 971–979. doi:10.17222/mit.2016.108.

L. Yang, G. Cheng, S. Li, M. Zhao, G. Feng, Generation Mechanism of TiN Inclusion for GCr15SiMn during Electroslag Remelting Process, ISIJ International. 55 (2015) 1901–1905. doi:10.2355/isijinternational.ISIJINT-2015-253.

L. Yang, G. Cheng, Characteristics of Al2O3, MnS, and TiN inclusions in the remelting process of bearing steel, International Journal of Minerals, Metallurgy, and Materials. 24 (2017) 869–875. doi:10.1007/s12613-017-1472-8.

D.A.R. Kay, R.J. Pomfret, Removal of oxide inclusions during AC electroslag remelting, J IRON STEE INST. 209 (1971) 962–965.

J. Fu, J. Zhu, Change of oxide inclusions during electroslag remelting process, Acta Metall. Sin. 7 (1964) 250–262.

D. Zhou, X. Chen, J. Fu, P. Wang, J. Li, M. Xu, Inclusions in electroslag remelting and continuous casting bearing steels, Journal of University of Science and Technology Beijing(China). 22 (2000) 26–30.

Z.B. Li, W.H. Zhou, Y.D. Li, Mechanism of removal of non-metallic inclusions in the ESR process, Iron Steel. 15 (1980) 20–26.

Z.B. Li, J.W. Zhang, X.Q. Che, Control of content and composition of non-metallic inclusion in ESR steel, J. Iron Steel Res. 9 (1997) 7.

A. Mitchell, Oxide inclusion behaviour during consumable electrode remelting, Ironmaking Steelmaking. 1 (1974) 172–179.

F. Wang, X.C. Chen, H.J. Guo, Influences of adding aluminum on inclusions in H13 steel through P–ESR, in: Advanced Materials Research, Trans Tech Publ, 2012: pp. 218–226.

B. Zuzek, M. Sedla, B. Podgornik, Effect of segregations on mechanical properties and crack propagation in spring steel, Frattura Ed Integrità Strutturale. (2015).

C.-B. Shi, X.-C. Chen, H.-J. Guo, Z.-J. Zhu, H. Ren, Assessment of oxygen control and its effect on inclusion characteristics during electroslag remelting of die steel, Steel Research International. 83 (2012) 472–486.

Published
2020/01/29
How to Cite
Ali, M., Porter, D., Kömi, J., Heikkinen, E.-P., Eissa, M., El Faramawy, H., & Mattar, T. (2019). The Effect of Electroslag Remelting on the Cleanliness of CrNiMoWMnV Ultrahigh-Strength Steels. Journal of Mining and Metallurgy, Section B: Metallurgy, 55(3), 381-395. Retrieved from https://aseestant.ceon.rs/index.php/jmm/article/view/20533
Issue
Vol. 55 No. 3 (2019)
Section
Original Scientific Paper

Authors retain copyright of the published papers and grant to the publisher the non-exclusive right to publish the article, to be cited as its original publisher in case of reuse, and to distribute it in all forms and media.

The Author(s) warrant that their manuscript is their original work that has not been published before; that it is not under consideration for publication elsewhere; and that its publication has been approved by all co-authors, if any, as well as tacitly or explicitly by the responsible authorities at the institution where the work was carried out. The Author(s) affirm that the article contains no unfounded or unlawful statements and does not violate the rights of others. The author(s) also affirm that they hold no conflict of interest that may affect the integrity of the Manuscript and the validity of the findings presented in it. The Corresponding author, as the signing author, warrants that he/she has full power to make this grant on behalf of the Author(s). Any software contained in the Supplemental Materials is free from viruses, contaminants or worms.

The published articles will be distributed under the Creative Commons Attribution ShareAlike 4.0 International license (CC BY-SA).

Authors are permitted to deposit publisher's version (PDF) of their work in an institutional repository, subject-based repository, author's personal website (including social networking sites, such as ResearchGate, Academia.edu, etc.), and/or departmental website at any time after publication.

Upon receiving the proofs, the Author(s) agree to promptly check the proofs carefully, correct any typographical errors, and authorize the publication of the corrected proofs.

The Corresponding author agrees to inform his/her co-authors, of any of the above terms.