Synthesis of submicronic α-alumina from local aluminum slags
Abstract
In this study, a high valued product submicronic α-alumina was successfully extracted from aluminum slags generated by the local aluminum industry. The extraction technique was based on the leaching of slags by H2SO4 followed by precipitation. The coarser aluminum-rich fractions of the slags were used in this study instead of the finer oxide-rich fractions that were commonly used in previous studies. The precipitation of the leached slags by NH4OH was controlled by a zetameter in order to determine the optimal precipitation pH. Then, the obtained gel showing the higher precipitation rate and the finer particle size was calcined at 1200 °C and characterized by the XRF, XRD, FTIR, SEM, EDS, and laser granulometry. Even without any pretreatment of slags, the XRF analysis revealed that a high purity and high extraction efficiency of 99.2% and 93.75% respectively could be achieved just at a leaching acid concentration of 15%. The XRD spectrum shows that the produced alumina was pure -corundum, which was confirmed by the FTIR spectrum showing only the Al-O bonds. The laser granulometry showed that the recovered powder exhibited a wide particle size distribution, which was between 50 nm and 20 µm, while the average particle size (d50) was about 400 nm. The SEM observations revealed that the grains were in the form of submicronic whiskers. The above characteristics allowed the obtained alumina powder in this study to be used in the usual applications of alumina such as refractory, ceramic fibers, abrasive, etc. The obtained powders may also assume applications as a thermally stable substitute for the commonly used transition alumina powders, which needs further investigations in future studies.
References
[1] X. Su, J. Li, Low temperature synthesis of single-crystal alpha alumina platelets by calcining bayerite and potassium sulfate, Journal of Materials Science & Technology, 27 (11) (2011) 1011–1015. https://doi.org/10.1016/S1005-0302(11)60179-5
[2] Y. Huang, Y. Xia, Q. Long, S. Liao, Y. Li, J. Liang, J. Cai, Large-scale synthesis of aluminum borate nanowires by a simple molten salt method, Ceramics International, 41(2) (2015) 2607–2610. https://doi.org/10.1016/j.ceramint.2014.10.012
[3] G. Feng, W. Jiang, J. Liu, C. Li, Q. Zhang, L. Miao, Q. Wu, Novel nonaqueous precipitation synthesis of alumina powders, Ceramics International, 43 (16) (2017) 13461–13468. https://doi.org/10.1016/j.ceramint.2017.07.050
[4] L. Liu, X. Zhang, L. Zhu, Y. Wei, C. Guo, H. Li, Preparation of hexagonal micro-sized α-Al2O3 platelets from a milled Al(OH)3 precursor with NH4F and NH4Cl additives, Zeitschrift für Naturforschung B, 74 (7-8) (2019) 579–583. https://doi.org/10.1515/znb-2019-0080
[5] S.H. Lim, K.Y. Zeng, C.B. He, Morphology, tensile and fracture characteristics of epoxy - alumina nanocomposites, Materials Science and Engineering: A, 527 (21-22) (2010) 5670–5676. https://doi.org/10.1016/j.msea.2010.05.038
[6] W.L. Suchanek, J.M. Garces, P.F. Fulvio, M. Jaroniec, Hydrothermal synthesis and surface characteristics of novel alpha alumina nanosheets with controlled chemical composition, Chemistry of Materials, 22 (24) (2010) 6564–6574. https://doi.org/10.1021/cm102158w
[7] G. Paglia, C.E. Buckley, A.L. Rohl, R.D. Hart, K. Winter, A.J. Studer, B.A. Hunter, J.V. Hanna, Boehmite derived γ-alumina system. 1. Structural evolution with temperature, with the identification and structural determination of a new transition phase, γ ‘-alumina, Chemistry of Materials, 16 (2) (2004) 220–236. https://doi.org/10.1021/cm034917j
[8] Y. Wang, J. Wang, M. Shen, W. Wang, Synthesis and properties of thermostable γ-alumina prepared by hydrolysis of phosphide aluminum, Journal of Alloys and Compounds, 467 (1-2) (2009) 405–412. https://doi.org/10.1016/j.jallcom.2007.12.007
[9] G.P. Johnston, R. Muenchausen, D.M. Smith, W. Fahrenholtz, S. Foltyn, Reactive laser ablation synthesis of nanosize alumina powder, Journal of the American Ceramic Society, 75 (12) (1992) 3293–3298. https://doi.org/10.1111/j.1151-2916.1992.tb04424.x
[10] T. Ogihara, H. Nakajima, T. Yanagawa, N. Ogata, K. Yoshida, N. Matsushita, Preparation of monodisperse, spherical alumina powders from alkoxides, Journal of the American Ceramic Society, 74 (9) (1991) 2263-2269. https://doi.org/10.1111/j.1151-2916.1991.tb08294
[11] E. Kato, K. Daemon, M. Nanbu, Decomposition of two aluminum sulfates and characterization of the resultant aluminas, Journal of the American Ceramic Society, 64 (8) (1981) 436–443. https://doi.org/10.1111/j.1151-2916.1981.tb09892
[12] H. Noda, K. Muramoto, H. Kim, Preparation of nano-structured ceramics using nanosized Al2O3 particles, Journal of Materials Science, 38 (9) (2003) 2043–2047. https://doi.org/10.1023/A:1023553925110
[13] I.N. Bhattacharya, P.K. Gochhayat, P.S. Mukherjee, S. Paul, P.K. Mitra, Thermal decomposition of precipitated low bulk density basic aluminium sulfate, Materials Chemistry and Physics, 88 (1) (2004) 32–40. https://doi.org/10.1016/j.matchemphys.2004.04.024
[14] M.C. Shinzato, R. Hypolito, Solid waste from aluminum recycling process: characterization and reuse of its economically valuable constituents, Waste Management, 25 (1) (2005) 37–46. https://doi.org/10.1016/j.wasman.2004.08.005
[15] P.E. Tsakiridis, Aluminium salt slag characterization and utilization–A review, Journal of Hazardous Materials, 217 (1) (2012) 1–10. https://doi.org/10.1016/j.jhazmat.2012.03.052
[16] S.O. Adeosun, O.I. Sekunowo, O.O. Taiwo, W.A. Ayoola, A. Machado, Physical and Mechanical Properties of Aluminum Dross, Advances in Materials, 3 (2) (2014) 6. https://doi.org/10.11648/j.am.20140302.11
[17] A. Gil, S.A. Korili, Management and valorization of aluminum saline slags: Current status and future trends, Chemical Engineering Journal, 289 (1) (2016) 74–84. https://doi.org/10.1016/j.cej.2015.12.069
[18] A. Meshram, K.K. Singh, Recovery of valuable products from hazardous aluminum dross: A review, Resources, Conservation and Recycling, 130 (1) (2018) 95–108. https://doi.org/10.1016/j.resconrec.2017.11.026
[19] T. Hiraki, A. Nosaka, N. Okinaka, T. Akiyama, Synthesis of zeolite-X from waste metals, ISIJ International, 49 (10) (2009) 1644–1648. https://doi.org/10.2355/isijinternational.49.1644
[20] S. Sangita, N. Nayak, C.R. Panda, Extraction of aluminium as aluminium sulphate from thermal power plant fly ashes, Transactions of Nonferrous Metals Society of China, 27 (9) (2017) 2082–2089. https://doi.org/10.1016/S1003-6326(17)60231-0
[21] F.H. Kamil, A. Salmiaton, R.M.H.R. Shahruzzaman, R. Omar, A.G. Alsultsan, Characterization and application of aluminum dross as catalyst in pyrolysis of waste cooking oil, Bulletin of Chemical Reaction Engineering, 12 (1) (2017) 81–88. https://doi.org/10.9767/bcrec.12.1.557.81-88
[22] E.A. El-Katatny, S.A. Halawy, M.A. Mohamed, M.I. Zaki, Surface composition, charge and texture of active alumina powders recovered from aluminum dross tailings chemical waste, Powder Technology, 132 (2-3) (2003) 137–144. https://doi.org/10.1016/S0032-5910(03)00047-0
[23] M.S. Reddy, D. Neeraja, Aluminum residue waste for possible utilisation as a material: a review, Indian Academy of Sciences, 43 (8) (2018) 124. https://doi.org/10.1007/s12046-018-0866-2
[24] M.S.R. Sarker, M.Z. Alam, M.R. Qadir, M.A. Gafur, M. Moniruzzaman, Extraction and characterization of alumina nanopowders from aluminum dross by acid dissolution process, International Journal of Minerals, Metallurgy and Materials, 22 (4) (2015) 429–436. https://doi.org/10.1007/s12613-015-1090-2
[25] T. Hiraki, T. Miki, K. Nakajima, K. Matsubae, S. Nakamura, T. Nagasaka, Thermodynamic analysis for the refining ability of salt flux for aluminum recycling, Materials, 7 (8) (2014) 5543–5553. https://doi.org/10.3390/ma7085543
[26] B.R. Das, B. Dash, B.C. Tripathy, I.N. Bhattacharya, S.C. Das, Production of η-alumina from waste aluminium dross, Minerals Engineering, 20 (3) (2007) 252–258. https://doi.org/10.1016/j.mineng.2006.09.002
[27] B. Dash, B.C. Tripathy, I.N. Bhattacharya, T. Subbaiah, A comparative study on the precipitation of hydrated alumina from different sources, International Journal of Metallurgical Engineering, 1 (1) (2012) 78–82. https://doi. org/10.5923/j.ijmee.20120105.02
[28] E. David, J. Kopac, Aluminum recovery as a product with high added value using aluminum hazardous waste, Journal of Hazardous Materials, 261 (1) (2013) 316–324. https://doi.org/10.1016/j.jhazmat.2013.07.042
[29] M. Mahinroosta, A. Allahverdi, A promising green process for synthesis of high purity activated-alumina nanopowder from secondary aluminum dross, Journal of Cleaner Production, 179 (1) (2018) 93–102. https://doi.org/10.1016/j.jclepro.2018.01.079
[30] F. Karouia, Traitement thermique de boehmite de taille et forme de particules contrôlées: vers l’optimisation des propriétés de l’alumine gamma, PhD Thesis, Toulouse III-Paul Sabatier University, 2014.
[31] H. Zhang, D. Zhu, S. Grasso, C. Hu, Tunable morphology of aluminum oxide whiskers grown by hydrothermal method, Ceramics International, 44 (13) (2018) 14967–14973. https://doi.org/10.1016/j.ceramint.2018.05.072
[32] A.S. Brown, M.A. Spackman, R.J. Hill, The electron distribution in corundum. A study of the utility of merging single-crystal and powder diffraction data, Acta Crystallographica Section A, 49 (3) (1993) 513–527. https://doi.org/10.1107/S0108767392011267
[33] J. Shah, M. Ranjan, V. Davariya, S.K. Gupta, Y. Sonvane, Temperature-dependent thermal conductivity and viscosity of synthesized α-alumina nanofluids, Applied Nanoscience, 7 (8) (2017) 803–813. https://doi.org/10.1007/s13204-017-0594-7
[34] K.C. Song, S.E. Pratsinis, The effect of alcohol solvents on the porosity and phase composition of titania, Journal of Colloid and Interface Science, 231 (2) (2000) 289–298. https://doi.org/10.1006/jcis.2000.7147
[35] J.K. Pradhan, I.N. Bhattacharya, S.C. Das, R.P. Das, R.K. Panda, Characterisation of fine polycrystals of metastable η-alumina obtained through a wet chemical precursor synthesis, Materials Science and Engineering: B, 77 (2) (2000) 185–192. https://doi.org/10.1016/S0921-5107(00)00486-4
[36] J.S. Lee, H.S. Kim, N.-K. Park, T.J. Lee, M. Kang, Low temperature synthesis of α-alumina from aluminum hydroxide hydrothermally synthesized using [Al(C2O4)x (OH)y] complexes, Chemical Engineering Journal, 230 (1) (2013) 351–360. https://doi.org/10.1016/j.cej.2013.06.099
[37] S. Pu, L. Li, J. Ma, F. Lu, J. Li, Disperse fine equiaxed alpha alumina nanoparticles with narrow size distribution synthesised by selective corrosion and coagulation separation, Scientific Reports, 5 (1) (2015) 11575. https://doi.org/10.1038/srep11575
[38] N. Kanhere, K. Rafiz, G. Sharma, Z. Sun, Y. Jin, Y.S. Lin, Electrode-coated alumina separators for lithium-ion batteries-effect of particle size and distribution of alumina powders, Powder Technology, 353 (1) (2019) 230–237. https://doi.org/10.1016/j.powtec.2019.05.007
[39] K. Nakahira, T. Hotta, M. Naito, N. Shinohara, Y. Cho, S. Katori, H. Emoto, T. Yamada, T. Takahashi, M. Okumiya, Characterization of coarse particles in alumina powders by a wet sieving method, Journal of the European Ceramic Society, 23 (10) (2003) 1661–1666. https://doi.org/10.1016/S0955-2219(02)00361-8
[40] C.J. Papini, W.K. Yoshito, D. Gouvêa, R.M.L. Neto, Particle size distribution analysis of an alumina powder: influence of some dispersants, pH and supersonic vibration, Materials Science Forum, (498-499) (2005)73–78. https://doi.org/10.4028/www.scientific.net/MSF.498-499.73
[41] M. Mahinroosta, A. Allahverdi, Hazardous aluminum dross characterization and recycling strategies: A critical review, Journal of Environmental Management, 223 (1) (2018) 452–468. https://doi.org/10.1016/j.jenvman.2018.06.068
Authors retain copyright of the published papers and grant to the publisher the non-exclusive right to publish the article, to be cited as its original publisher in case of reuse, and to distribute it in all forms and media.
The Author(s) warrant that their manuscript is their original work that has not been published before; that it is not under consideration for publication elsewhere; and that its publication has been approved by all co-authors, if any, as well as tacitly or explicitly by the responsible authorities at the institution where the work was carried out. The Author(s) affirm that the article contains no unfounded or unlawful statements and does not violate the rights of others. The author(s) also affirm that they hold no conflict of interest that may affect the integrity of the Manuscript and the validity of the findings presented in it. The Corresponding author, as the signing author, warrants that he/she has full power to make this grant on behalf of the Author(s). Any software contained in the Supplemental Materials is free from viruses, contaminants or worms.The published articles will be distributed under the Creative Commons Attribution ShareAlike 4.0 International license (CC BY-SA).
Authors are permitted to deposit publisher's version (PDF) of their work in an institutional repository, subject-based repository, author's personal website (including social networking sites, such as ResearchGate, Academia.edu, etc.), and/or departmental website at any time after publication.
Upon receiving the proofs, the Author(s) agree to promptly check the proofs carefully, correct any typographical errors, and authorize the publication of the corrected proofs.
The Corresponding author agrees to inform his/her co-authors, of any of the above terms.