The effect on wear behavior of the amount of Y2O3 doped to the MA6000 alloy produced by mechanical alloying method

Keywords: Mechanical alloy; Superalloy; MA6000; Wear; Y2O3

Abstract


This paper investigated the wear performances of Y2O3 doped MA6000 (Ni-Cr-Al) alloy produced by mechanical alloying (MA). Produced, all powders were pre-formed by cold pressing and sintered in a vacuum environment. Sintered MA6000-X% Y2O3 superalloys were characterized by scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), X-ray diffraction (XRD) analysis, density, and hardness measurements. Wear tests of Y2O3 added MA6000 alloys were carried out in a block-on-ring type wear device. In the wear tests, the sliding speed of 1 ms-1 at room temperature (RT) was performed under five different sliding distances (200-1000m) and three different loads (5 N, 10 N, and 15 N). As a result of the studies, it was determined that the MA’ed MA6000 superalloy powders were homogeneous and flake shape. With the increase amount of Y2O3, hardness of these superalloys increased from 267 to 431 Hv, but the density slightly decreased. Different intermetallic/carbur phases such as Ni3Al, MoC are observed in all compositions. Wear tests show that weight loss and wear rate decreased, and friction coefficient (µ) increased with the increasing amount of Y2O3 additive. Besides, it was determined that as the applied load increased in the wear test, the weight loss increased, but the wear rate and friction coefficient (µ) decreased.

References

[1]      M. Mujahid, C.-A. Gater, J.-W. Martin, Microstructural Study of a Mechanically Alloyed ODS Superalloy, Journal of Materials Engineering and Performance, 7 (1998) 524–532. https://doi.org/10.1361/105994998770347684


[2]      R.-L. Dreshfield, Defects in Nickel-Base Superalloys, Journal of metals, 39 (1987) 16–21. https://doi.org/10.1007/BF03258034


[3]      Y. Xu, L. Zhang, J. Li, X. Xiao, X. Cao, G. Jia, Z. Shen, Relationship between Ti/Al ratio and stress-rupture properties in nickel-based superalloy, Materials Science and Engineering A, 544 (2012) 48–53. https://doi.org/10.1016/j.msea.2012.03.006


[4]      D. Sun, C. Liang, J. Shang, J. Yin, Y. Song, W. Li, T. Liang, X. Zhang, Effect of Y 2 O 3 contents on oxidation resistance at 1150 °C and mechanical properties at room temperature of ODS Ni-20Cr-5Al alloy, Applied Surface Science, 385 (2016) 587–596. https://doi.org/10.1016/j.apsusc.2016.05.143


[5]      Y.-L. Chen, A.-R. Jones, Reduction of porosity in oxide dispersion-strengthened alloys produced by powder metallurgy, Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science, 32 (2001) 2077–2085. https://doi.org/10.1007/s11661-001-0019-8


[6]      S. Ukai, K. Taya, K. Nakamura, M.-S. Aghamiri, N. Oono, S. Hayashi, T. Okuda, Directional recrystallization by zone annealing in a Ni-based ODS superalloy, Journal of Alloys and Compounds, 744 (2018) 204–210. https://doi.org/10.1016/j.jallcom.2018.01.406


[7]      I. Baker, B. Iliescu, J. Li, H.-J. Frost, Experiments and simulations of directionally annealed ODS MA 754, Materials Science and Engineering A, 492 (2008) 353–363. https://doi.org/10.1016/j.msea.2008.03.032


[8]      J.-K. Gregory, J.-C. Gibeling, W.-D. Nix, High temperature deformation of ultra-fine-grained oxide dispersion strengthened alloys, Metallurgical Transactions A, 16 (1985) 777–787. https://doi.org/10.1007/BF02814828


[9]      M. Nganbe, M. Heilmaier, High temperature strength and failure of the Ni-base superalloy PM 3030, International Journal of Plasticity, 25 (2009) 822–837. https://doi.org/10.1016/j.ijplas.2008.06.005


[10]    W. Hoffelner, R.-F. Singer, High-cycle fatigue properties of the ODS-alloy MA 6000 at 850 °C, Metallurgical Transactions A, 16 (1985) 393–399. https://doi.org/10.1007/BF02814337


[11]    A. Korashy, H. Attia, V. Thomson, S. Oskooei, Characterization of fretting wear of cobalt-based superalloys at high temperature for aero-engine combustor components, Wear, 330–331 (2015) 327–337. https://doi.org/10.1016/j.wear.2014.11.027


[12]    C. Suryanarayana, Mechanical Alloying: A Novel Technique to Synthesize Advanced Materials, Research, 2019 (2019) 1–17. https://doi.org/10.34133/2019/4219812


[13]    R. Sundaresan, F.-H. Froes, Mechanical Alloying, Journal of metals, 39 (1987) 22–27. https://doi.org/10.1007/BF03258604


[14]    C.-C. Koch, J.-D. Whittenberger, Mechanical milling/alloying of intermetallics, Intermetallics, 4 (1996) 339–355. https://doi.org/10.1016/0966-9795(96)00001-5


[15]    H.-I. Gharsallah, A. Sekri, M. Azabou, L. Escoda, J.-J. Suñol, M. Khitouni, Structural and Thermal Study of Nanocrystalline Fe-Al-B Alloy Prepared by Mechanical Alloying, Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science, 46 (2015) 3696–3704. https://doi.org/10.1007/s11661-015-2966-5


[16]    S.-K. Kang, R.-C. Benn, Characterization of INCONEL alloy MA 6000 powder, Metallurgical Transactions A, 18 (1987) 747–752. https://doi.org/10.1007/BF02646916


[17]    C. Vincent, J.-F. Silvain, J.-M. Heintz, N. Chandra, Effect of porosity on the thermal conductivity of copper processed by powder metallurgy, Journal of Physics and Chemistry of Solids, 73 (2012) 499–504. https://doi.org/10.1016/j.jpcs.2011.11.033


[18]    E.-O. Ezugwu, J. Bonney, Y. Yamane, An overview of the machinability of aeroengine alloys, Journal of Materials Processing Technology, 134 (2003) 233–253. https://doi.org/10.1016/S0924-0136(02)01042-7


[19]    O. Palavar, D. Özyürek, A. Kalyon, Artificial neural network prediction of aging effects on the wear behavior of IN706 superalloy, Materials and Design, 82 (2015) 164–172. https://doi.org/10.1016/j.matdes.2015.05.055


[20]    S. Li, Q. Wei, Y. Shi, C.-K. Chua, Z. Zhu, D. Zhang, Microstructure Characteristics of Inconel 625 Superalloy Manufactured by Selective Laser Melting, Journal of Materials Science and Technology, 31 (2015) 946–952. https://doi.org/10.1016/j.jmst.2014.09.020


[21]    Y.-M. He, J.-G. Yang, S.-J. Chen, Z. Li, Z.-L. Gao, Effect of high-temperature aging on microstructure and mechanical properties of Ni-Mo-Cr based superalloy subjected to simulated heat-affected zone thermal cycle, Journal of Alloys and Compounds, 660 (2016) 266–275. https://doi.org/10.1016/j.jallcom.2015.11.129


[22]    Q. Wu, H. Song, R.-W. Swindeman, J.-P. Shingledecker, V.K. Vasudevan, Microstructure of long-term aged IN617 Ni-base superalloy, Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science, 39 (2008) 2569–2585. https://doi.org/10.1007/s11661-008-9618-y


[23]    A. Szczotok, K. Rodak, Microstructural studies of carbides in MAR-M247 nickel-based superalloy, IOP Conference Series: Materials Science and Engineering, 35 (2012) 012006. https://doi.org/10.1088/1757-899X/35/1/012006


[24]    L. Zhang, X. Chen, D. Li, C. Chen, X. Qu, X. He, Z. Li, A comparative investigation on MIM418 superalloy fabricated using gas- and water-atomized powders, Powder Technology, 286 (2015) 798–806. https://doi.org/10.1016/j.powtec.2015.09.023


[25]    J. Belan, GCP and TCP Phases Presented in Nickel-base Superalloys, Materials Today: Proceedings, 3 (2016) 936–941. https://doi.org/10.1016/j.matpr.2016.03.024


[26]    X. Wang, Y. Zhou, Z. Zhao, Z. Zhang, Effects of Solutioning on the Dissolution and Coarsening of γ′ Precipitates in a Nickel-Based Superalloy, Journal of Materials Engineering and Performance, 24 (2015) 1492–1504. https://doi.org/10.1007/s11665-014-1368-y


[27]    Frisk, Andersson, Rogberg, Cast Structure in Alloy A286, an Iron-Nickel Based Superalloy, Metals, 9 (2019) 711. https://doi.org/10.3390/met9060711


[28]    Y. Nunomura, Y. Kaneno, H. Tsuda, T. Takasugi, Phase relation and microstructure in multi-phase intermetallic alloys based on Ni3Al-Ni3Ti-Ni3V pseudo-ternary alloy system, Intermetallics, 12 (2004) 389–399. https://doi.org/10.1016/j.intermet.2003.12.011


[29]    T. Kosorukova, G. Firstov, H. NoËl, V. Ivanchenko, Crystal structure changes in the Ni3Ta intermetallic compound, Chemistry of Metals and Alloys, 6 (2013) 196–199. https://doi.org/10.30970/cma6.0270


[30]    P. Li, J. Zhang, S. Ma, H. Jin, Y. Zhang, W. Zhang, First-principles investigations on structural, elastic, electronic properties and Debye temperature of orthorhombic Ni3Ta under pressure, Philosophical Magazine, 98 (2018) 1641–1655. https://doi.org/10.1080/14786435.2018.1453619


[31]    L. Cheng, X. Yu, J. Zhang, W. Li, C. Zhao, Z. Wang, L. Jin, DFT investigations into surface stability and morphology of δ-MoC catalyst, Applied Surface Science, 497 (2019) 143790. https://doi.org/10.1016/j.apsusc.2019.143790


[32]    Y. Liu, Y. Jiang, J. Feng, R. Zhou, Elasticity, electronic properties and hardness of MoC investigated by first principles calculations, Physica B: Condensed Matter, 419 (2013) 45–50. https://doi.org/10.1016/j.physb.2013.03.016


[33]    K. Zhao, L.-H. Lou, Y.-H. Ma, Z.-Q. Hu, Effect of minor niobium addition on microstructure of a nickel-base directionally solidified superalloy, Materials Science and Engineering A, 476 (2008) 372–377. https://doi.org/10.1016/j.msea.2007.06.041


[34]    G. Zhu, S. Zhao, R. Wang, A. Dong, L. Zhang, W. Wu, W. Wang, S. Jiang, Y. Pu, Oxide reinforced Ni base composite prepared by spark plasma sintering, MATEC Web of Conferences, 130 (2017) 8–10. https://doi.org/10.1051/matecconf/201713003008


[35]    M. Hajizadeh-Oghaz, R.-S. Razavi, M. Barekat, M. Naderi, S. Malekzadeh, M. Rezazadeh, Synthesis and characterization of Y2O3 nanoparticles by sol–gel process for transparent ceramics applications, Journal of Sol-Gel Science and Technology, 78 (2016) 682–691. https://doi.org/10.1007/s10971-016-3986-3.


[36]    S. Ikeno, I. Siota, M. Nobuki, M. Nakamura, Wear properties of oxide dispersion strengthened nickel alloys, Journal of Materials Science, 30 (1995) 4401–4406. https://doi.org/10.1007/BF00361524


[37]    D. Özyürek, M. Yildirim, I. Çiftçi, The tribological properties of A356-SiCpmetalmatrix composites fabricated by thixomoulding technique, Science and Engineering of Composite Materials, 19 (2012) 351–356. https://doi.org/10.1515/secm-2012-0012


[38]    K.-G. Thirugnanasambantham, S. Natarajan, Mechanistic studies on degradation in sliding wear behavior of IN718 and Hastelloy X superalloys at 500 °c, Tribology International, 101 (2016) 324–330. https://doi.org/10.1016/j.triboint.2016.04.016


[39]    C.-N. Panagopoulos, K.-I. Giannakopoulos, V. Saltas, Wear behavior of nickel superalloy, CMSX-186, Materials Letters, 57 (2003) 4611–4616. https://doi.org/10.1016/S0167-577X(03)00370-7


[40]    S.-M. Banijamali, Y. Palizdar, S. Najafi, A. Sheikhani, M. Soltan Ali Nezhad, P. Valizadeh Moghaddam, H. Torkamani, Effect of Ce Addition on the Tribological Behavior of ZK60 Mg-Alloy, Metals and Materials International, 27 (2021) 2732–2742. https://doi.org/10.1007/s12540-020-00832-4


[41]    M.-H. Ghassemi, V. Abouei, M. Moshtaghi, M.-T. Noghani, The effect of removing worn particles by ultrasonic cleaning on the wear characterization of LM13 alloy, Surface Engineering and Applied Electrochemistry, 51 (2015) 382–388. https://doi.org/10.3103/S1068375515040067


[42]    A. Amanov, Improvement in mechanical properties and fretting wear of Inconel 718 superalloy by ultrasonic nanocrystal surface modification, Wear, 446–447 (2020) 203208. https://doi.org/10.1016/j.wear.2020.203208


[43]     Y.-H. Lee, I.-S. Kim, S.-S. Kang, H.-D. Chung, A study on wear coefficients and mechanisms of steam generator tube materials, Wear, 250 (2001) 718–725. https://doi.org/10.1016/S0043-1648(01)00680-9

Published
2022/11/01
How to Cite
Şelik, Şaban, Özyürek, D., & Tunçay, T. (2022). The effect on wear behavior of the amount of Y2O3 doped to the MA6000 alloy produced by mechanical alloying method. Journal of Mining and Metallurgy, Section B: Metallurgy, 58(2), 285-297. Retrieved from https://aseestant.ceon.rs/index.php/jmm/article/view/35865
Issue
Vol. 58 No. 2 (2022)
Section
Original Scientific Paper

Authors retain copyright of the published papers and grant to the publisher the non-exclusive right to publish the article, to be cited as its original publisher in case of reuse, and to distribute it in all forms and media.

The Author(s) warrant that their manuscript is their original work that has not been published before; that it is not under consideration for publication elsewhere; and that its publication has been approved by all co-authors, if any, as well as tacitly or explicitly by the responsible authorities at the institution where the work was carried out. The Author(s) affirm that the article contains no unfounded or unlawful statements and does not violate the rights of others. The author(s) also affirm that they hold no conflict of interest that may affect the integrity of the Manuscript and the validity of the findings presented in it. The Corresponding author, as the signing author, warrants that he/she has full power to make this grant on behalf of the Author(s). Any software contained in the Supplemental Materials is free from viruses, contaminants or worms.

The published articles will be distributed under the Creative Commons Attribution ShareAlike 4.0 International license (CC BY-SA).

Authors are permitted to deposit publisher's version (PDF) of their work in an institutional repository, subject-based repository, author's personal website (including social networking sites, such as ResearchGate, Academia.edu, etc.), and/or departmental website at any time after publication.

Upon receiving the proofs, the Author(s) agree to promptly check the proofs carefully, correct any typographical errors, and authorize the publication of the corrected proofs.

The Corresponding author agrees to inform his/her co-authors, of any of the above terms.